Motorcycle Lift Tables & Shop Equipment

HMC 30"x70" Welding Table (SWT-3070-P)

This HMC welding table gives you a full 30 inch by 70 inch steel top that raises and lowers to match the job in front of you. The table has 7 height settings, from about 23 inches up to 40 inches, and holds up to 1,200 pounds of work and fixturing on top...

HMC 30"x86" Motorcycle Lift (SL-3086)

This lift table gives you a full 30 inch by 86 inch platform and holds up to 1,200 pounds. It's sized for everything from mopeds and scooters to full-size cruisers. The closed height is just 7 1/2 inches, and the 32 inch ramp is low and long enough that...

HMC 30"x90" Motorcycle Lift (SL-3090)

This lift table gives you a 30 inch by 90 inch platform that holds up to 1,200 pounds. It comes with a 32 inch ramp sized for everything from small scooters to full-size cruisers. The table ships right side up and ready to connect to air, so you don't...

HMC 30"x90" Motorcycle Lift - Double Cylinder (DCSL-3090)

This lift uses two cylinders instead of one, so it can raise up to 2,100 pounds — almost double what a standard 1,200 pound table can handle. It's built on the same 30 inch by 90 inch platform as the SL-3090, so you get the extra lifting power without...

HMC Cam Bearing - SL Series (2515-A)

This is a single replacement cam bearing for SL Series lift tables. Order it on its own if only one bearing has worn out and the rest of the set is still good. Technical Specifications Part Type: Cam Bearing Compatible With: SL Series lift...

HMC Cam Bearing Kit - SL Series (SLB-2.38 Kit)

This kit gives you a complete set of cam bearings for your SL Series lift table — all 4 bearings and the snap rings that go with them, in one purchase. It's the better deal if you're replacing the full set instead of just one bearing. Technical...

HMC Caster Set - SL Series (SLC-4)

This caster set lets you roll your SL Series table around the shop instead of dragging it across the floor. It's built for shops that move lifts between bays often, or that need to clear floor space in a hurry. Technical Specifications Color: Black ...

HMC Condor Wheel Chock - SL Series (SC-2000)

This Condor wheel chock holds the front wheel upright on your SL Series table without clamping down on the fork. It's a quick way to steady a bike for general service work when you don't need the wheel completely locked down the way a cycle vise holds it...

HMC Cycle Vise - SL Series (CV-2049)

This cycle vise clamps the front wheel down tight to your SL Series table. With the wheel locked in place, you get both hands free for tire changes, fork work, and brake service — no second person needed to hold the bike steady while you work. Technical...

HMC Cylinder Seal Repair Kit - AC-2085 (AC-2085-Repair Kit)

This seal repair kit rebuilds the AC-2085 cylinder, and it also fits HMC's 6 inch cylinders and Handy Vintage 6 inch cylinders. It's a lower-cost fix for when the cylinder body itself is still good and only the seals have worn out. Technical...

HMC Foot Valve, Air Operated - SL Series (FV-250)

This air-operated foot valve controls the height on your SL Series lift table. Replace it when the valve starts sticking, leaking air, or won't hold the table's position reliably anymore. Technical Specifications Type: Air Operated, Center Stop ...

HMC Front/Rear Extension Kit - SL-3090 (SL-3090-F/REXK)

This kit extends your lift table's working length at either the front or the back end, instead of adding width the way the side extensions do. It bolts on without changing your table's 1,200 pound weight rating. Technical Specifications Rated...