Loading... Please wait...
Find the Exact Part that fits your machine

Hover over image to zoom

  • Image 1

Yamaha YZ125 Clarke Fuel Tank

Your Price:
$229.99
Item #:
Clarke Gas Tanks-20
Shipping:
Calculated at checkout

Details & Specs

 

 

 

 

Clarke Fuel tanks are Made of High Impact Plastic

 

Uses stock mounts and petcock.

 

New Cap Included.(Except #1337 and 1335, 1404, 1408) These use stock cap.

 

Not all pictures are the actual tank

 

Shown with optional Dry Break Receiver

 

Clarke Fuel tanks come in any color listed on the Color Chart.

 

 

 

 

 

 

 

 

 

**NOTE On 2005-2012 Aluminum framed models: The Yamaha factory padding under the tank is too hard and tall to allow this tank to properly sit down enough to mount.

 

You can either trim the ribs from the padding to provide clearance or remove them completely and use Clarke tank padding or pad the frame yourself using locally sourced product.

Product Reviews

Write review

  1. stock size gas tank holds 23oz less than stock and its a bad fit. this Clarke tank is not a good one. 1 Star Review

    Posted by on Nov 12th 2017

    I got this stock size gas tank for my 2014 yz125 and it holds 32oz less than the stock tank and stock plastic doz not line up on it very good, I'm taking it back off of my bike, it's junk.


  2. Stock volume 1991 YZ125 tank 1 Star Review

    Posted by on Nov 10th 2017

    The quality of the tank was not as good as one would hope. The bottom of the tank was bubbled and there was a stressed area that almost looked like a crack (it didn't leak, but I would suspect that it may in the future = weak point).
    Also there are some areas on the tank with sharp edges where you are likely to wear out your pants. They did cut down the sharp edges in the most obvious places, but fell short in finishing the job completely.
    In spite of all this, I attempted to mount the tank on the bike, but found it impossible to complete the install as, at two locations, the threaded brass inserts were not on center with the dimples in the tank. As a result, the radiator shrouds could not be bolted to the tank. (It was so far off center, I couldn't get a single thread to start. I couldn't even hold the bolt at an angle and cross thread it - just couldn't get the threads to engage, no matter what I tried.
    In addition, the dimples in the tank are too small to allow any wiggle room for the shroud to be manipulated into lining up the hole with the off center brass insert.
    I even went as far as to modified my shroud, by hogging out the hole on one, but this did not alleviate the issue, because even though I got the hole to line up with the off center brass insert, the shroud didn't have enough room to allow for a bolt/washer to fit in it without rubbing on the side of it's dimple, thus the bolt would not go straight down = again no engagement of threads.
    Basically, the tank fabrication tolerances are very poor, so I could not install the radiator shrouds, thus this tank is a pointless purchase.
    Finally (on a side note), I also wonder why Clarke would go so far as to make a tank that is OEM volume, but requires the use of their aftermarket cap (the OEM cap will not thread on this tank). I have to ask, "Doesn't it seem logical, that if you're making a tank that is an OEM replacement (volume), shouldn't that tank also accept the OEM cap, too?"
    In any case, I am in process of trying to return the defective tank and get my payment back (in full), since the product was completely impossible to use. Since I am just starting this return, the verdict is out, at this point, as whether or not they have good customer service OR not.
    I may increase the star rating, if the customer service turns out to be good.
    Final note: I tried to save some money by purchasing the Clarke tank, as it is the only one with the same volume as the OEM tank. (I don't want or need a high volume tank). In the end, since I have, (so far) tried to install it, then had to remove it, then take pictures of the issues with it, then pursue response from the company I purchased it through, etc... and I am still not done returning it.... It occurs to me that my time is valuable and that I should've just paid more and bought the OEM tank directly from Yamaha. It would've cost me more, up front, but in the end it would've saved me a lot of time and effort.


  3. Great tank 4 Star Review

    Posted by on Jan 20th 2017

    I think this tank is great. Well made and yellow color is excellent. It would have gotten 5 stars but I have to completely remove tank padding from my late model yz 125 in order to make room and fit it. Otherwise a quality product. James


Product Notice

All fuel tanks sold are designed for off road use only in California and are not guaranteed in any way for street use unless specified. It is the full responsibility of the end user to determine if these products are suitable for their application in their respective area. Please check with your local and state regulations before running a tank on the highway.

Join Our Email List

Connect With Us

The Enduro Shop
JustGasTanks.com
(760) 757-6269
Monday-Friday: 8am to 6pm

Safe & Secure Shopping

Click the button below to add the Yamaha YZ125 Clarke Fuel Tank to your wish list.